Same Day Service
Get started with a FREE quote
Years of Experience
Quality Products and Service
SURFACE PREPARATION
1. Properly prepare surface according to NWFA approved methods.
2. Use a No. 100 grit screen [80 grit for 201 White] for the final sanding cut.
3. Remove all dust with a broom and/or vacuum and tack surface with a clean towel moistened with mineral spirits.
APPLICATION
1. Stir or shake material thoroughly before and occasionally during use. Apply a test sample on a small inconspicuous area before proceeding with entire job. If desired, DuraSeal® Penetrating Finish #210 Neutral can be used to lighten any standard Penetrating Finish color.
2. Apply the first coat of DuraSeal® Penetrating Finish liberally with a brush, lambs wool applicator or cloth at a coverage rate of approximately 500 square feet per gallon.
3. Allow to penetrate for 5 - 8 minutes then remove excess by wiping with rags or by buffing with #2 steel wool. Removal of all excess material is essential to ensure proper dry time.
4. If desired, apply a thin second coat at a coverage rate of approximately 800 square feet per gallon. Allow to penetrate and remove excess material in the same manner as the first coat [step 3 above].
NOTE: A second coat of DuraSeal® Penetrating Finish is not recommended with 350 VOC compliant material.
5. Allow the final coat to dry at least 8 hours [for best results overnight] and apply a finish coat of your choice.
NOTE: For heavy traffic commercial applications, it is recommended that DuraSeal® Penetrating Finish be used without a finish coat, and periodically maintained with DuraSeal® Renovator Cleaner and Reconditioner.
PRECAUTION
Do not use steel wool when using DuraSeal® Penetrating Finish #201 White.
IMPORTANT
Immediately after use, place rags, steel wool and other waste in a sealed, water filled metal container. See cautionary statement.
DRY TIME & CURE
Approximately 8 hours to overnight. NOTE: Drying time will be increased by high humidity, low temperature, lack of air movement or incomplete removal of excess stain.
COVERAGE
First coat - approximately 500 square feet per gallon. (Optional second coat - approximately 800 square feet per gallon.) A second coat is not recommended when using 350 VOC compliant material
Services
Dura Seal Quickcoat
Description
DuraSeal® Quick Coat Penetrating Finish is a semi-transparent stain formulated to seal, color and provide exceptional durability when used on bare wood and masonry surfaces. This rich blend of oil and resin gives hardwood floors a soft, satiny sheen. Its unique formulation provides a surface that can be topcoated in two hours. DuraSeal® Quick Coat Penetrating Finish is available in existing DuraSeal® colors as well as many Certified Minwax® colors. It can be used with or without a finish coat, and is compatible with all DuraSeal® water-borne and oil-modified finish systems.
- Finishes
- Water Based
- Oil Based
- Water Based
DURASEAL PENETRATING STAIN
DESCRIPTION
DuraSeal® Penetrating Finish is a semi-transparent stain formulated to seal, color and provide exceptional durability when used on bare wood and masonry surfaces. This rich blend of oil and resin gives hardwood floors a soft, satiny sheen. Available in colors to match any decor, DuraSeal® Penetrating Finish creates a bond with the wood that won't scratch or wear away. Can be used with or without a finish coat.
- Mullican Flooring
SURFACE PREPARATION
1. Properly prepare floor according to NWFA specifications. Use a No.100 grit screen for the final screening cut.
2. Remove all dust with a vacuum and tack surface with a clean cloth moistened with mineral spirits.
APPLICATION
1. Shake material thoroughly before and occasionally during use. Apply to a small test area before proceeding with the entire job to ensure desired color. If desired, DuraSeal® Quick Coat Penetrating Finish #110 Neutral can be used to lighten any standard DuraSeal® wood tone.
2. Apply the first coat of DuraSeal® Quick Coat Penetrating Finish liberally with a brush, lambswool applicator or cloth at approximately 500 square feet per gallon.
3. Allow to penetrate for 5-8 minutes, then remove excess by wiping with rags or by buffing with #2 steel wool. Removal of all excess material is essential to ensure proper dry time and adhesion of the finish coat.
4. If desired, apply a thin second coat at a coverage rate of approximately 800 square feet per gallon. Allow to penetrate and remove excess material in the same manner as the first coat (step 3 above).
5. Allow the final coat to dry at least 2 hours and apply a DuraSeal® finish coat of your choice.
IMPORTANT
Place rags, steel wool and other waste immediately after use in a sealed, water-filled metal container. See cautionary statement
DRY TIME AND CURE
Approximately 2-3 hours. Note: Dry time is based on conditions of 77° and 50% relative humidity.
COVERAGE
First coat - approximately 500 square feet per gallon. Optional second coat - approximately 800 sq.ft. per gallon.